Deciding the size of a hydraulic power pack requires balancing pressure, flow rate, and motor dimension to achieve optimal performance for its task. Picking the correct hydraulic power pack is crucial for keeping machinery funcional, reducing wasted energy, and avoiding equipment breakdowns. This guide outlines essential sizing factors, explains required calculations, and offers advice on choosing the right design.
Selecting the correct size for a hydraulic power unit is essential because a unit that is too small might struggle to meet the system’s needs, causing it to overheat, use more energy, and possibly fail earlier. On the other hand, a unit that is too big might waste energy, produce too much heat, and wear out parts too quickly. Correct sizing ensures that each part of the hydraulic system runs well and performs at a top level.
Pressure determines the force that the hydraulic power pack can apply. Calculating the pressure required is essential based on the load and size of the hydraulic actuator or cylinder. Pressure is typically measured in bars or PSI.
To determine the correct pressure, use the design calculations:
Pressure (bar) = Force (N) / Area (cm²)
For example, if a hydraulic cylinder needs to lift 10,000 N, and its piston has an area of 50 cm², the pressure required would be:
10,000 N / 50 cm² = 200 bar
This figure provides a baseline for selecting a hydraulic power pack capable of delivering the necessary force.
The flow rate, measured in litres per minute (LPM) or gallons per minute (GPM), dictates the speed of movement for the hydraulic actuators. This factor directly influences the speed at which the hydraulic cylinder extends or retracts and motors rotate.
To calculate the flow rate:
For example, if a cylinder with a displacement of 1 litre needs to complete a cycle in 10 seconds, the required flow rate would be 6 LPM.
High-speed applications require a faster flow rate per minute, while low-speed applications can work with a lower flow rate. Pump types are determined by flow rate and pressure requirements.
The motor or engine provides the energy to drive the hydraulic pump. Its power rating is typically measured in kilowatts (KW) or horsepower (HP). The motor must match the pressure and flow rate requirements to ensure smooth operation and avoid excessive wear.
To determine the required motor power, use this formula:
Motor Power (kW) = (Flow Rate (L/min) × Pressure (bar)) / 600
For instances, if a power pack needs a flow rate of 10 L/min and operates at 250 bar, the motor power required would be:
(10 × 250) / 600 = 4.17 kW
Ensuring adequate motor power is crucial for maintaining hydraulic performance without overheating or inefficiency.
The reservoir stores the hydraulic fluid, maintaining and aids air separation and heat dissipation. A correctly sized reservoir prevents overheating and ensures the system has sufficient fluid for high-demand situations.
Generally, the reservoir should hold three to five times the flow rate per minute. For instance, if the flow rate is 10 LPM, the reservoir should be sized between 30 and 50 litres to ensure proper system cooling and fluid availability.
The valves and components of the hydraulic circuit guide the movement and speed of the hydraulic fluid. Directional control valves direct the fluid's direction, while pressure relief valves keep the system from becoming too pressurised by keeping the pressure below the safe limit.
Valves must be sized to correctly handle the systems maximum pressure and flow rate needs. Picking the right valves allows accurate hydraulic system control and avoids problems like pressure loss and poor performance.
Each calculation contributes to choosing the right hydraulic power pack design to handle the system requirements without excessive energy use or component stress.
With the key calculations in place, it’s time to choose a hydraulic power pack that meets your specific application. Here are some tips:
Look at your system’s performance requirements, including pressure, flow rate, and power needs. For instance, an industrial press may require a high flow and pressure power pack, while mobile equipment could need a compact solution.
When sizing, consider potential future expansion. If your machinery may require increased force or speed, choose a power pack with extra capacity. This approach saves time and costs by preventing the need for a complete replacement later.
The operating environment affects the type of power pack you choose. Hydraulic power packs for outdoor or mobile equipment should be rugged, and could be driven electrically or with a combustion engine. Consideration needs to be given to the operation environment; some could require zone rating, some marinising and others could need to be dust resistant. It is important to consider this at the design stage as it can prove challenging to address this once the system has been built.
Choose high-quality hydraulic components that compliment the power pack’s function. These include control valves, filtration systems to prevent contaminants, and a hydraulic tank designed for easy fluid circulation. Suitable components ensure trouble-free operation and reduce system wear.
Understanding and calculating pressure, flow rate, motor power and tank size helps you pick the right hydraulic power pack. Proper sizing means efficient energy use, longer life, and smoother hydraulic system performance.
Posted by admin in category Hydraulic Power Packs Advice on Wednesday, 7th May 2025
Call our knowledgeable team Mon–Fri 8:30am–5pm
Systems & Components Division 01427 874445
sales@hydrastore.co.uk
Hose Division 0121 326 6395
hoses@hydrastore.co.uk